13559553569

泉州聯進機械有限公司

quanzhou lianjin machine co., ltd

數

控

切

條

機

使

用

說

明

cnc cutting machine

用途：用于橡膠切條、切紙等。

特點：1.裝有防護裝置在使用時安全快捷。

              2.上下切割，切料精準度高，最細可切至1mm.

　　　 3.采用伺服電機加觸摸屏控制，操作方便、高效率。

使用說明

公共設備電力：電壓380v,50hz。

主電源線：2.5平方毫米  四芯線

1. 機械運轉中手切勿接觸刀模及滾輪。

2. 橡膠片應該保持平整進料，防止卡料。

3. 操作時不要雙層料同時切，以免燒壞電機，發現送料滾筒卷料時，要及時關機清理，同時如有雜料在刀口工作部位要及時清理幹淨，清理時務必斷開電源來源。

4. 原料不能有鐵，石頭等雜物，如發現要清理幹淨，以免損傷刀片。

5. 發現電機有異聲，要停機檢查，鏈條皮帶松動要及時調整，螺絲松動要及時緊固。

6. 機台工作時，手一定不要伸進裏面，如有問題，一定要停機解決。

7. 汽泵指針一般在3pma左右，太大或太小氣壓都會影響切膠效果。

8. 如時間長，發現料切不斷

①調整刀口間隙。

②修整刀口，檢查刀口是否有損壞，如有損壞要及時修整。

9. 易損件部位要保持油路暢通潤滑。

10. 新機台用少量粉撒在卷筒上，以免卷料。

11. 膠片進料有跑偏需調整兩邊氣缸壓力。

purpose: this machine is used for cutting the rubber, paper etc.

advantage: 1.equiped with safety cover to secure safety on working.

                   2. up-down cut high accuracy. the minimum can be cut to1mm.  

                   3. servo motor and touch screen control, easy to operate, high efficiency.

instructions:

public equipment：power: 380v,50hz.

host power line:  2.5mm² four-core

1. do not touch the cutter die and roller during the operation of the machine.

2. rubber sheet should be kept flat to prevent material from sticking.

3. when operating, do not cut rubber in double-deck at one time, which will cause the motor to be too hot and broken. if the material-sending roller can not run smoothly. please shutdown at once; meanwhile, if there are odds and ends at knife edge, please clean up in time .do stop the power before cleaning.

4. no iron or stone in the material; if any, take them, away at once, so as not to make the blade damaged.

5. any unusual voice, stop and check. adjust chains and screws if they are loose.

6. do stop the machine when there is problem. do not put hands in when the machine is still working.

7. the indicator of the air pump is at about 3pma. too large or too small air pressure may have an effect on slicing.

8. after being operated for long time and the machine fails to cut off material. 

① adjust the blade clearance.

② customer should adjust the knife and check whether the blade is damaged and need repairing.

9. kept the wearing parts being smooth & lubricative.

10. new machine please add proper amount of powder to the rooller to avoid material rolling and jammed.

11. if the film feed is out of alignment, adjust the cylinder pressure on both sides.